Damage effects on the windmilling aerodynamics of low pressure ratio fans

During engine operation, if there is an engine shut-down, the engine will enter a windmilling state, where the fan will continue to spin due to the ram pressure but no work will be generated. It is critical in the development of future low pressure ratio turbofan designs to characterise the drag and rotational speed of the engine fan at windmill. This project aims to address this, by using both numerical and experimental methods to investigate the aerodynamic flow field at windmill. As this condition will often occur following damage to the engine, blade damage will also be considered during the investigation. A single stream vertical low speed rig in the Whittle Laboratory will be modified to be representative of a future turbofan engine design. These modifications will include the redesign of hub and casing lines, as well as the rotor and stator blades. The blades will be further modified in the later stages of the project to include typical in-service damage patterns. Measurements will then be taken in this rig to investigate the fan flow field at windmill. The experimental study will be complemented with numerical simulations of the fan design with and without blade damage. The main expected outcomes from this project are design recommendations for future low fan pressure ratio engines, as well as the development of a low order modelling tool that can be used in industry to predict drag and rotational speed of the fan in windmill for different blade damage levels.

1. Impact on the UK Aero-Propulsion and Power Generation Industry
The UK Propulsion and Power sector is undergoing disruptive change. Electrification is allowing a new generation of Urban Air Vehicles to be developed, with over 70 active programmes planning a first flight by 2024. In the middle of the aircraft market, companies like Airbus and Rolls-Royce, are developing boundary layer ingestion propulsion systems. At high speed, Reaction Engines Ltd are developing complex new air breathing engines. In the aero gas turbine sector Rolls-Royce is developing UltraFan, its first new architecture since the 1970s. In the turbocharger markets UK companies such as Cummins and Napier are developing advanced turbochargers for use in compounded engines with electrical drive trains. In the power generation sector, Mitsubishi Heavy Industries and Siemens are developing new gas turbines which have the capability for rapid start up to enable increased supply from renewables. In the domestic turbomachinery market, Dyson are developing a whole new range of miniature high speed compressors. All of these challenges require a new generation of engineers to be trained. These engineers will need a combination of the traditional Aero-thermal skills, and new Data Science and Systems Integration skills. The Centre has been specifically designed to meet this challenge.

Over the next 20 years, Rolls-Royce estimates that the global market opportunities in the gas turbine-related aftercare services will be worth over US$700 billion. Gas turbines will have 'Digital Twins' which are continually updated using engine health data. To ensure that the UK leads this field it is important that a new generation of engineer is trained in both the underpinning Aero-thermal knowledge and in new Data Science techniques. The Centre will provide this training by linking the University and Industry Partners with the Alan Turing Institute, and with industrial data labs such as R2 Data Labs at Rolls-Royce and the 'MindSphere' centres at Siemens.

2. Impact on UK Propulsion and Power Research Landscape
The three partner institutions (Cambridge, Oxford and Loughborough) are closely linked to the broader UK Propulsion and Power community. This is through collaborations with universities such as Imperial, Cranfield, Southampton, Bath, Surrey and Sussex. This will allow the research knowledge developed in the Centre to benefit the whole of the UK Propulsion and Power research community.

The Centre will also have impact on the Data Science research community through links with the CDT in Data Centric Engineering (DCE) at Imperial College and with the Alan Turning Institute. This will allow cross-fertilization of ideas related to data science and the use of advanced data analytics in the Propulsion and Power sectors.

3. Impact of training a new generation of engineering students
The cohort-based training programme of the current CDT in Gas Turbine Aerodynamics has proved highly successful. The Centre's independent Advisory Group has noted that the multi-institution, multi-disciplinary nature of the Centre is unique within the global gas turbine training community, and the feedback from cohorts of current students has been extremely positive (92% satisfaction rating in the 2015 PRES survey). The new CDT in Future Propulsion and Power will combine the core underlying Aero-thermal knowledge of the previous CDT with the Data Science and Systems Integration skills required to meet the challenges of the next generation. This will provide the UK with a unique cohort of at least 90 students trained both to understand the real aero-thermal problems and to have the Data Science and Systems Integration skills necessary to solve the challenges of the future.