Developing crack resistant polymer composite matrices for liquid hydrogen storage

Lead Research Organisation: University of Bristol
Department Name: Aerospace Engineering

Abstract

With the international effort to reach Net Zero by 2050, the aviation industry is in a race to adopt zero-carbon emission fuel sources within the coming decades. It is widely accepted that liquid hydrogen (LH2), a cryogenic liquid stored at 20 K (-253 degrees celsius), will serve as this fuel source for the majority of the aircraft market, as it offers a better payload and range to alternative solutions such as batteries or gaseous hydrogen. Nevertheless, there are many challenges associated with the transition to liquid hydrogen that the aviation industry will need to overcome. One significant challenge is the storage of LH2 aboard the aircraft. While metallic tanks are currently used in the space industry for single-use LH2 launch vehicles and are likely to be first to market in civil aviation; carbon fibre reinforced polymer (CFRP) tanks offer significant gravimetric efficiency benefits which, over the multi-cycle 20-25-year lifetime of a tank, translates to considerable cost savings. While CFRP tanks are considered promising long-term storage vessels, the susceptibility of the polymer matrix to microcracking at these extremely low temperatures is currently a primary barrier to adoption. There are a number of issues with microcracking in this application, not least the safety and thermal issues associated with increased hydrogen permeation, but also the integrity of the tank being compromised and the chance of liquid hydrogen boil off within crack networks causing delamination or tank rupture.

Matrix microcracking at cryogenic temperatures is understood to be caused by the build-up of thermally induced residual stresses through several possible mechanisms. On the microscopic level, the mismatch of co-efficient of thermal expansion (CTE) between the fibre and matrix leads to residual stresses in both constituents during thermal cycling. On the next level of structural hierarchy, the mismatch of effective CTE between adjacent plies with varying fibre orientation is a possible cause. In addition to this, when cooled down to cryogenic temperatures a material can experience thermal shock via inhomogeneous temperature distributions, where neighbouring domains encounter different temperatures, creating a steep temperature gradient across the material. This can also result in the development of transient thermally induced stresses and in turn cause microcracking. The overarching aim of this project is therefore to develop a polymer composite matrix which can withstand repeated exposure to a 20 K cryogenic environment without microcracking and be suitable for use in LH2 storage tanks. To address this, the key objectives of this project include:

- Determine, through a design of experiments testing approach, which polymeric molecular properties or toughening methods enable matrices with the desired thermomechanical and physical properties to supress microcracking

- Design and synthesise new matrices or adapt existing materials to incorporate these material properties or toughening methods

- Characterisation of these matrix materials to validate the design process and subsequent manufacture of composite panels using the best candidates

- Design and conduct a rigorous testing campaign to characterise the composite materials with respect to the key performance indicators for LH2 tanks, such as microcrack fracture toughness, hydrogen permeability and resistance to cracking under repeated cryogenic cycling

Planned Impact

There are seven principal groups of beneficiaries for our new EPSRC Centre for Doctoral Training in Composites Science, Engineering, and Manufacturing.

1. Collaborating companies and organisations, who will gain privileged access to the unique concentration of research training and skills available within the CDT, through active participation in doctoral research projects. In the Centre we will explore innovative ideas, in conjunction with industrial partners, international partners, and other associated groups (CLF, Catapults). Showcase events, such as our annual conference, will offer opportunities to a much broader spectrum of potentially collaborating companies and other organisations. The supporting companies will benefit from cross-sector learning opportunities and

- specific innovations within their sponsored project that make a significant impact on the company;
- increased collaboration with academia;
- the development of blue-skies and long-term research at a lowered risk.

2. Early-stage investors, who will gain access to commercial opportunities that have been validated through proof-of-concept, through our NCC-led technology pull-through programme.

3. Academics within Bristol, across a diverse range of disciplines, and at other universities associated with Bristol through the Manufacturing Hub, will benefit from collaborative research and exploitation opportunities in our CDT. International visits made possible by the Centre will undoubtedly lead to a wider spectrum of research training and exploitation collaborations.

4. Research students will establish their reputations as part of the CDT. Training and experiences within the Centre will increase their awareness of wider and contextually important issues, such as IP identification, commercialisation opportunities, and engagement with the public.

5. Students at the partner universities (SFI - Limerick) and other institutions, who will benefit from the collaborative training environment through the technologically relevant feedback from commercial stakeholder organisations.

6. The University of Bristol will enhance their international profile in composites. In addition to the immediate gains such as high quality academic publications and conference presentations during the course of the Centre, the University gains from the collaboration with industry that will continue long after the participants graduate. This is shown by the

a) Follow-on research activities in related areas.
b) Willingness of past graduates to:

i) Act as advocates for the CDT through our alumni association;
ii) Participate in the Advisory Board of our proposed CDT;
iii) Act as mentors to current doctoral students.

7. Citizens of the UK. We have identified key fields in composites science, engineering and manufacturing technology which are of current strategic importance to the country and will demonstrate the route by which these fields will impact our lives. Our current CDTs have shown considerable impact on industry (e.g. Rolls Royce). Our proposed centre will continue to give this benefit. We have built activities into the CDT programme to develop wider competences of the students in:

a) Communication - presentations, videos, journal paper, workshops;
b) Exploitation - business plans and exploitation routes for research;
c) Public Understanding - science ambassador, schools events, website.

Publications

10 25 50

Studentship Projects

Project Reference Relationship Related To Start End Student Name
EP/S021728/1 30/09/2019 30/03/2028
2747462 Studentship EP/S021728/1 30/09/2021 30/11/2025 James Griffith