SAMULET_Project_2_Combustion Systems for Low Environmental Impact
Lead Research Organisation:
University of Oxford
Department Name: Engineering Science
Abstract
Abstracts are not currently available in GtR for all funded research. This is normally because the abstract was not required at the time of proposal submission, but may be because it included sensitive information such as personal details.
Publications
Abbey B
(2012)
Neutron strain tomography using Bragg-edge transmission
in International Journal of Materials Research
Baimpas N
(2013)
The application of geometry corrections for Diffraction Strain Tomography (DST) analysis of a Ni-base superalloy blade
in Powder Diffraction
Baimpas N
(2013)
Stress evaluation in thin films: Micro-focus synchrotron X-ray diffraction combined with focused ion beam patterning for do evaluation
in Thin Solid Films
Clark JN
(2013)
Ultrafast three-dimensional imaging of lattice dynamics in individual gold nanocrystals.
in Science (New York, N.Y.)
Constantinescu A
(2013)
Symbolic and numerical solution of the axisymmetric indentation problem for a multilayered elastic coating
in International Journal of Solids and Structures
Fleury R
(2017)
Characterisation of handling and service surface damage on Nickel alloys caused by low velocity impacts of blunt hard objects
in Mechanics of Materials
Jun T
(2012)
Residual stress characterization in 12%-Cr steel friction stir welds by neutron diffraction
in The Journal of Strain Analysis for Engineering Design
Kim T.
(2013)
Feasibility study of synchrotron x-ray diffraction and absorption spectroscopy for the characterisation of NMC oxides for Li-ion battery cathodes
in Lecture Notes in Engineering and Computer Science
Kirkwood H
(2017)
High resolution imaging and analysis of residual elastic strain in an additively manufactured turbine blade
in International Journal of Nanotechnology
Korsunsky A
(2012)
Analysis of the internal structure and lattice (mis)orientation in individual grains of deformed CP nickel polycrystals by synchrotron X-ray micro-diffraction and microscopy
in International Journal of Fatigue
Korsunsky A.M.
(2012)
X-ray texture analysis and imaging of engineering materials at oxford HEX-lab
in Lecture Notes in Engineering and Computer Science
Korsunsky A.M.
(2012)
Experimentally validated numerical modeling of material deformation across the scales: A review
in Lecture Notes in Engineering and Computer Science
Liu W
(2013)
Grain refinement and fatigue strengthening mechanisms in as-extruded Mg-6Zn-0.5Zr and Mg-10Gd-3Y-0.5Zr magnesium alloys by shot peening
in International Journal of Plasticity
Liu W
(2011)
Improvement of fatigue properties by shot peening for Mg-10Gd-3Y alloys under different conditions
in Materials Science and Engineering: A
Lunt A
(2018)
On the origins of strain inhomogeneity in amorphous materials
in Scientific Reports
Lunt A
(2017)
Characterisation of nanovoiding in dental porcelain using small angle neutron scattering and transmission electron microscopy.
in Dental materials : official publication of the Academy of Dental Materials
Ma L
(2013)
Fundamental Formulation for Transformation Toughening in Anisotropic Solids
in Journal of Applied Mechanics
Malik A
(2013)
Deep reactive ion etching of silicon moulds for the fabrication of diamond x-ray focusing lenses
in Journal of Micromechanics and Microengineering
Mostafavi M
(2013)
Three-dimensional crack observation, quantification and simulation in a quasi-brittle material
in Acta Materialia
Nguyen G
(2012)
How to connect two scales of behaviour in constitutive modelling of geomaterials
in Géotechnique Letters
Pandey A
(2017)
In situ and operando studies of structural and functional materials and systems using electron, ion and X-ray microscopy
in Materials & Design
Robinson I
(2017)
Materials & Design Virtual Special Issue Editorial: Analysis of material microstructure and defects using X-ray and neutron beams - Size-Strain
in Materials & Design
Romano Brandt L
(2017)
Probing the deformation and fracture properties of Cu/W nano-multilayers by in situ SEM and synchrotron XRD strain microscopy
in Surface and Coatings Technology
Salvati E
(2018)
Nanoscale structural damage due to focused ion beam milling of silicon with Ga ions
in Materials Letters
Description | For the processes considered (linear friction welding and direct laser metal sintering), new numerical models were developed and validated against experimental data. |
Exploitation Route | Incorporation of the methods developed in this project into the design procedures used by companies such as Rolls-Royce. Validated numerical models used to optimise processing operations and thus to ensure best performance of engineering components and assemblies. |
Sectors | Aerospace, Defence and Marine,Construction,Creative Economy,Electronics,Energy,Environment,Manufacturing, including Industrial Biotechology,Transport |
URL | http://www.korsunsky.org |
Description | 3D printing is revolutionising manufacturing. We made (and are continuing to make) our contribution to understanding the structural integrity (strength and fracture toughness) of materials and components obtained by this route. |
First Year Of Impact | 2012 |
Sector | Aerospace, Defence and Marine,Chemicals,Construction,Energy,Environment,Manufacturing, including Industrial Biotechology,Transport |
Impact Types | Societal,Economic |
Description | Birmingham Dental School |
Organisation | University of Birmingham |
Department | School of Dentistry |
Country | United Kingdom |
Sector | Academic/University |
PI Contribution | We advise colleagues at Birmingham School of Dentistry on modern nanoscale characterisation techniques, and implications of these novel approaches for clinical, diagnostic, therapeutic and prosthetic dentistry. |
Collaborator Contribution | We work closely with Birmingham School of Dentistry who provide access to expertise in clinical, diagnostic, therapeutic and prosthetic dentistry, and supply samples for our microscopy and X-ray studies. |
Impact | Multiple publications, joint designs of experiments |
Description | DLS |
Organisation | Diamond Light Source |
Country | United Kingdom |
Sector | Private |
PI Contribution | We provide scientific leadership, ideas for tests, expertise and manpower for running complex experiments. |
Collaborator Contribution | Access to unique world class synchrotron beam lines. |
Impact | Multi-disciplinary - engineering, physics, chemistry; use of X-ray scattering, spectroscopy, imaging |